Lab Objective:

The objective of this lab exercise is for you to learn and understand how to secure VTP domains using Cisco Catalyst Switches. By default, VTP domains are not password-protected.

Lab Purpose:

Securing the VTP domain is a fundamental skill. When VTP domains are not configured with a password, rogue switches can be added to the network and disrupt service. As a Cisco engineer, as well as in the Cisco CCNA exam, you will be expected to know how to configure VTP passwords.

Certification Level:

This lab is suitable for both CCENT and CCNA certification exam preparation.

Lab Difficulty:

This lab has a difficulty rating of 4/10.

Readiness Assessment:

When you are ready for your certification exam, you should complete this lab in no more than 5 minutes.

Lab Topology:

Please use the following topology to complete this lab exercise:

Lab 8: Securing VTP Domains 2

Task 1:

In preparation for VLAN configuration, configure a hostname on Sw1 and Sw2 as depicted in the topology.

Task 2:

Configure and verify Sw1 as a VTP server switch and configure Sw2 as a VTP client switch. Both switches should be in the VTP domain named CISCO. Secure VTP messages with the VTP password CISCO.

Task 3:

Configure and verify FastEthernet0/1 between Sw1 and Sw2 as an 802.1q trunk.

Task 4:

Configure and verify VLANs 10 to 40 on Sw1 with the names provided above. Validate that these VLANs are still propagated to Sw2 after VTP has been secured.

Configuration and Verification

Task 1:

For reference information on configuring hostnames, please refer to the previous labs.

Task 2:

NOTE: By default, Cisco switches are VTP servers so no configuration is necessary for server mode on Sw1. This can be verified using the show vtp status command. However, you do need to configure the domain.

Sw1#config t 
Enter configuration commands, one per line.  End with CTRL/Z. 
Sw1(config)#vtp domain CISCO 
Changing VTP domain name from Null to CISCO 
Sw1(config)#vtp password CISCO 
Setting device VLAN database password to CISCO 
Sw1#show vtp status 
VTP Version                     : 2 
Configuration Revision           : 2 
Maximum VLANs supported locally : 250 
Number of existing VLANs        : 5 
VTP Operating Mode              : Server 
VTP Domain Name                 : CISCO 
VTP Pruning Mode                : Enabled 
VTP V2 Mode                     : Disabled 
VTP Traps Generation            : Disabled 
MD5 digest                      : 0x00 0x7A 0x5E 0x47 0xF1 0xDD 0xB5 0x30 

Sw2#config t 
Enter configuration commands, one per line.  End with CTRL/Z. 
Sw2(config)#vtp mode client 
Setting device to VTP CLIENT mode. 
Sw2(config)#vtp domain CISCO 
Changing VTP domain name from Null to CISCO 
Sw1(config)#vtp password CISCO
Setting device VLAN database password to CISCO 
Sw2(config)#end 
Sw2#show vtp status 
VTP Version                     : 2 
Configuration Revision           : 0 
Maximum VLANs supported locally : 250 
Number of existing VLANs        : 5 
VTP Operating Mode              : Client 
VTP Domain Name                 : CISCO 
VTP Pruning Mode                : Enabled 
VTP V2 Mode                     : Disabled 
VTP Traps Generation            : Disabled 
MD5 digest                      : 0x9D 0x1A 0x9D 0x16 0x9E 0xD1 0x38 0x59

Task 3:

For reference information on configuring and verifying trunks, please refer to earlier labs.

Task 4:

For reference information on configuring and verifying VLANs, please refer to previous labs.

Sw2#show vlan brief 

VLAN Name                    Status    Ports 
---- ---------------------- --------- ------------------------------- 
1    default                 active    Fa0/2, Fa0/3, Fa0/4, Fa0/5 
                                       Fa0/6, Fa0/7, Fa0/8, Fa0/9 
10   SALES                   active     
20   MANAGERS                active     
30   ENGINEERS               active     
40   SUPPORT                 active     
1002 fddi-default            active     
1003 token-ring-default      active     
1004 fddinet-default         active     
1005 trnet-default           active

NOTE: Make sure that the MD5 digest at the end of the output of the show vtp status  command is the same when VTP passwords have been configured on switches within the same VTP domain.

By admin

Leave a Reply

Your email address will not be published. Required fields are marked *

Ads Blocker Image Powered by Code Help Pro

Ads Blocker Detected!!!

We have detected that you are using extensions to block ads. Please support us by disabling these ads blocker.

Translate »